Design Issues of a High-Stroke,On-Blade Piezostack Actuator for a Helicopter Rotor with Trailing-Edge Flaps

Abstract

A compact actuator to oscillate blade trailing-edge flap on a full-scale helicopter has been investigated for vibration suppression. The actuator consists of piezoelectric stacks and a dual-stage mechanical stroke amplifier. It is recommended that commercially available piezostack be used for timely manufacturing and maintenance rather than a custom-designed piezostack. An analytical approach to estimate the maximum actuator force requirement for the rotor in hover condition is discussed first. A piezostack down-selection through the experimental evaluation is presented, which is to select a piezostack with high stiffness as well as good strain/block force output among twelve commercial piezostacks. The design requirements of on-blade piezoelectric actuator are discussed, and one-dimensional stiffness modeling and finite element beam modeling are presented to evaluate the analytical/numerical actuator performance. The prototype actuator with a double-lever stroke amplifier was fabricated and tested on bench-top as well as in vacuum chamber. An amplification factor of 19.4 and the consistent actuator output up to 600 g of centrifugal loading were obtained. An improved actuator has been designed with a design refinement to reduce structural losses.

References

Abbott, I. H. and Doenhoeff, A. E. V. 1959. Theory of Wing Sections, Dover Publications, Inc., New York.

Chandra, R. and Chopra, I. 1998. “Actuation of Trailing Edge Flap in a Wing Model Using Piezostack Device,” Journal of Intelligent Material Systems and Structures, 9(10): 847-853.

Chopra, I. 2000. “Status of Application of Smart Structures Technology to Rotorcraft Systems,” Journal of American Helicopter Society, 45(4): 228-252.

Giurgiutiu, V. , Rogers, C. A. and Chaudhry, Z. 1997. “Design of Displacement-Amplified Induced-Strain Actuators for Maximum Energy Output,” Journal of Mechanical Design, 119(4): 511-517.

Hall, S. R. , Tzianetopoulou, T. , Straub, F. and Ngo, H. 2000. “Design and Testing of a Double X-frame Piezoelectric Actuator,” in Proceedings of SPIE Conference on Smart Structures and Materials, 26-37, Newport Beach, CA.

IEEE Standards Board . 1987. IEEE Standard on Piezoelectricity, ANSI/IEEE, Std. 176.

Loewy, R. G. 1984. “Helicopter Vibrations, A Technologocal Perspective,” Journal of American Helicopter Society, 29(4): 3-20.

Meirovitch, L. 1986. Element of Vibration Analysis, McGraw-Hill, Inc.

Milgram, J. , Chopra, I. and Straub, F. 1998. “Rotors With Trailing Edge Flaps: Analysis and Comparison With Experimental Data,” Journal of American Helicopter Society, 43(4): 319-332.

10.

Mitrovic, M. , Carman, G. P. and Straub, F. K. 1999. “Electro-Mechanical Characterization of Piezoelectric Stack Actuators,” in Proceedings of SPIE Conference on Smart Structures and Materials, 586-601, Newport Beach, CA.

11.

North, J. 1997. Polytec PI, Inc., Personal communication.

12.

Physik Instrumente . 1997. Products for Micropositioning.

13.

Samak, D. K. and Chopra, I. 1996. “Design of High Force, High Displacement Actuators for Helicopter Rotors,” Smart Materials and Structures, 5: 58-67.

14.

Shigley, J. E. 1996. Standard Handbook of Machine Design, McGraw-Hill, second edition.

15.

Spencer, B. T. and Chopra, I. 1996. “Design and Testing of a Helicopter Trailing Edge Flap with Piezoelectric Stack Actuators,” in Proceedings of SPIE Conference on Smart Structures and Materials, 120-131, San Diego, CA.

16.

Straub, F. K. and Hassan, A. A. 1996. “Aeromechanic Considerations in the Design of a Rotor with Smart Material Actuated Trailing Edge Flaps,” in Proceedings of the 52nd Annual Forum of the American Helicopter Society, Washington, DC.

17.

Straub, F. K. , Ngo, H. T. , Anand, V. and Domzalski, D. B. 1999. “Development of a Piezoelectric Actuator for Trailing Edge Flap Control of Rotor Blades,” in Proceedings of SPIE Conference on Smart Structures and Materials, 2-13, Newport Beach, CA