Influence of the interteeth clearances on the flow ripple in a gerotor pump for engine lubrication

Abstract

A gerotor pump, which is widely used in the automotive industry for engine oil lubrication, produces an instantaneous flow fluctuation and the estimation of this is fundamental in order to evaluate the pump quality for silent and smooth operation. The intricate aspects of the pumping process of a gerotor pump make computational fluid dynamics the appropriate tool for modelling and simulation to provide insights into its flow characteristics. Because the instantaneous flow is rather dependent on the teeth contact, a new boundary condition of a virtual wall was developed, which allows simulation of the teeth contact in the interteeth radial clearances. This new boundary condition is utilized in a three-dimensional model of the gerotor pump with mesh deformation and remeshing at every time step by means of a home-made ad-hoc code programmed by the present authors and named viscous wall cell. The code has been integrated into the computational fluid dynamics solver. The interteeth clearances are studied under the following different operating conditions (working pressures and rotational velocities): first, no contact points (no teeth contact is studied in order to prove that, even if the interteeth radial clearance is sufficiently small, the leakage cannot be negligible); second, all contact points (the ideal approach is considered with zero interteeth radial clearances used to model zero manufacturing tolerances); third, one contact point at different locations (the existence of manufacturing tolerances and the teeth contact approach make the pump’s operation and its pumping mechanism more realistic in the simulation). The numerical instantaneous flow is compared with the analytical instantaneous flow, with the instantaneous flow modelled by using the bond graph technique, and with the experimental determination of the flow ripple for a specific unit. The results obtained show the importance of simulating the teeth contact and prove to be an excellent estimation of the instantaneous flow behaviour to obtain the dynamic properties of a gerotor pump under more realistic conditions than its design.

Keywords

Trochoidal-gear pump interteeth clearances teeth contact instantaneous flow three-dimensional unsteady computational fluid dynamics dynamic mesh

Get full access to this article

View all access options for this article.

References

Donea

Huerta

Ponthot

J-P

Rodriguez-Ferran

. Arbitrary Lagrangian–Eulerian methods. In: Estein

Borst

Hugues

TJR

(eds) Encyclopedia of computational mechanics, vol 1. New York: John Wiley, 2004, ch 14.

Voorde

Vierendeels

Dick

. Development of a Laplacian-based mesh generator for ALE calculations in rotary volumetric pumps and compressors. Comput Meth Appl Mech Engng 2004; 193: 4401–4415.

Strasser

. CFD investigation of gear pump mixing using deforming/agglomerating mesh. Trans ASME, J Fluids Engng 2007; 129(4): 476–484.

Houzeaux

Codina

. A finite element method for the solution of rotary pumps. Comput Fluids 2007; 36: 667–679.

Castilla

Gamez-Montero

Ertürk

. Numerical simulation of turbulent flow in the suction chamber of a gearpump using deforming mesh and mesh replacement. Int J Mech Sci 2010; 52: 1334–1342.

Suresh Kumar

Manonmani

. Computational fluid dynamics integrated development of gerotor pump inlet components for engine lubrication. Proc IMechE Part D: J Automobile Engineering 2010; 224(12): 1555–1567.

Biernacki

Stryczek

. Analysis of stress and deformation in plastic gears used in gerotor pumps. J Strain Analysis 2010; 45: 465–479.

Gamez-Montero

Codina

. Flow characteristics of a trochoidal-gear pump using bond graphs and experimental measurement Part 2. Proc IMechE Part I: J Systems and Control Engineering 2007; 221: 347–363.

ANSYS FLUENT 12.0.16 user’s guide. Canonsburg, Pennsylvania: ANSYS Inc., 2009.

10.

Sleiti

Kapat

. Comparison between EVM and RSM turbulence models in predicting flow and heat transfer in rib-roughened channels. J Turbulence 2006; 7(29): 1–21.

11.

Kaya

Karagoz

. Performance analysis of numerical schemes in highly swirling turbulent flows in cyclones. Curr Sci 2008; 94(10): 1273–1278.

12.

Patankar

. Numerical heat transfer and fluid flow. New York: Hemisphere Publishing Corporation, 1980.

13.

Date

. Fluid dynamical view of pressure checkerboarding problem and smoothing pressure correction on meshes with colocated variables. Int J Heat Mass Transfer 2003; 46: 4885–4898.

14.

Rhie

Chow

. Numerical study of the turbulent flow past an airfoil with trailing edge separation. AIAA J 1983; 21(11) 1525–1532.

15.

Issa

. Solution of implicitly discretized fluid flow equations by operator splitting. J Comput Phys 1986; 62: 40–65.

16.

Ferzieger

Peric

. Computational methods for fluid dynamics. Berlin: Springer, 1996.

17.

Gamez-Montero

Castilla

Mujal

. GEROLAB package system: innovative tool to design a trochoidal-gear pump. Trans ASME, J Mech Des 2009; 131: 074502-1–074502-6.

18.

Launder

Spalding

. The numerical computation of turbulent flows. Comput Meth Appl Mech Engng 1974; 3: 269–289.

19.

Coussirat

van Beeck

Mestres

. Computational fluid dynamics modeling of impinging gas-jet systems: I. Assessment of eddy viscosity models. Trans ASME, J Fluids Engng 2005; 127(4): 691–703.