Investigation of force-assisted suction reed valves in hermetic reciprocating compressors

Abstract

Reed valves are widely used in hermetic reciprocating compressors and are responsible for a major share of thermodynamic losses. The suction valve in particular, which is opened for almost the entire suction phase, has a very significant improvement potential. Suction valves in hermetic reciprocating compressors are usually opened only by the pressure difference created by the moving piston and should be closed before the compression phase starts, in order to avoid a reversed mass-flow through the valve. The valves are thus preloaded, which, on the other hand, results in a higher flow resistance. In this work, a force-assisted suction valve is investigated. An electromagnetically actuated spring generates an additional force acting on the conventional suction reed valve. This force leads to a completely different valve movement and a significant reduction of the losses caused by the suction valve. A conventional suction valve flutters during the suction phase. Thus, it hits the valve seat several times which has, beside an increased flow resistance, negative influences on the reliability of the reed valve and noise emissions. With the help of the additional force, it is able to overcome the opening delay due to the preload and the oil ‘stiction’ effect. Furthermore, the suction valve can be held open during the whole suction phase, and it closes smoothly in time near the bottom dead centre of the piston. The investigation of the force-assisted suction valve is done by numerical simulations as well as by experiments. Results show an improvement of the coefficient of performance by approximately 0.7%–1.6% depending on the operating conditions.

Keywords

Reciprocating compressor reed valve suction loss CFD R600a

Get full access to this article

View all access options for this article.

References

Haas A. Innovation in reciprocating compressors by technology transfer from modern combustion engines. In: International compressor engineering conference, West Lafayette, USA, 25–28 July 2000, paper no. 1361, pp.1–8. West Lafayette: Purdue University.

Oliveira SJ and Real MA. Analytical and experimental study of discharge flow behaviour provided by electronically controlled valves in hermetic compressors. In: International compressor engineering conference, West Lafayette, USA, 12–15 July 2010, paper no. 1941, pp.1–8. West Lafayette: Purdue University.

Real MA and Pereira EAG. Using PV diagram synchronized with the valve functioning to increase the efficiency on the reciprocating hermetic compressor. In: International compressor engineering conference, West Lafayette, USA, 12–15 July 2010, paper no. 1225, pp.1–8. West Lafayette: Purdue University.

Bhakta A, et al. A valve design methodology for improved reciprocating compressor performance. In: International compressor engineering conference, West Lafayette, USA, 16–19 July 2012, paper no. 1252, pp.1–8. West Lafayette: Purdue University.

Nagata S, Nozaki T and Akizawa T. Analysis of dynamic behavior of suction valve using strain gauge in reciprocating compressor. In: International compressor engineering conference, West Lafayette, USA, 12–15 July 2010, paper no. 1273, pp.1–8. West Lafayette: Purdue University.

Burgstaller A, et al. Influence of the main parameters of the suction valve on the overall performance of a small hermetic reciprocating compressor. In: International compressor engineering conference, West Lafayette, USA, 14–17 July 2008, paper no. 1315, pp.1–8. West Lafayette: Purdue University.

Hopfgartner J, et al. Reduction of the suction losses through reed valves in hermetic reciprocating compressors using a magnet coil. In: IOP conference series: materials science and engineering, Volume 232 (2017), paper no. 012034, pp.1–10. IOP Publishing.

Costagliola M. Dynamics of a reed type valve. PhD Thesis, Massachusetts Institute of Technology, USA, 1949.

Khalifa HE and Liu X. Analysis of stiction effect on the dynamics of compressor suction valve. In: International compressor engineering conference, West Lafayette, USA, 14–17 July 1998, pp.81–92. West Lafayette: Purdue University.

10.

Nagy D, et al. Valve lift measurement for the validation of a compressor simulation model. In: International compressor engineering conference, West Lafayette, USA, 14–17 July 2008, paper no. 1274, pp.1–8. West Lafayette: Purdue University.

11.

Hopfgartner J, et al. Experimental study on the thermal behavior of a domestic refrigeration compressor during transient operation in a small capacity cooling system. In: International compressor engineering conference, West Lafayette, USA, 11–14 July 2016, paper no. 1216, pp.1–8. West Lafayette: Purdue University.

12.

Bathe

. Finite element procedures, New Jersey: Prentice Hall, 1996.