Topological characterization of vortex structures on a transonic compressor stator during the stalling process

Abstract

Numerical simulations, verified against experimental results, were used to study the stalling process of a transonic compressor. The method of topological analysis was used to study the distribution of the flow field on the blade surface in detail. In this manner, the steady three-dimensional vortex structure of the transonic compressor stator under transition conditions was established, and the mechanism of the stalling process was revealed from the perspective of the vortex structure evolution. The results show that in the process of stalling, as the back pressure increases, the separation areas on the suction side of the stator and the scale and strength of the separation vortex also increase, thereby weakening other vortices and causing a large amount of low-energy fluid to accumulate in the passage. Thus, the passage is blocked, and the through-flow capability of the compressor is reduced. In addition, because of the complex movement of the vortices and the transport of low-energy fluid clusters, the boosting capacity of the compressor is reduced, thus causing the compressor to stall.

Keywords

Transonic compressor stalling process vortex structure topological analysis numerical simulation

Get full access to this article

View all access options for this article.

References

Hah C, Schulze R, Wagner S, et al. Numerical and experimental study for short wavelength stall inception in a low-speed axial compressor[R]. ISABE99-7033, 1999.

Moore FK and Greitzer EM. A theory of post-stall transients in axial compression systems: part I-development of equations. ASME paper no.85-GT-171,1985.

Greizer EM and Moore FK. A theory of post-stall transients in axial compression systems: part II-application. ASME paper no. 85-GT-171, 1985.

Grarnier

Epstein

Greitzer

. rotating waves as a stall inception indication in axial compressors. ASME J Turbomach 1991; 113: 290–301.

Camp

Day

. A study of spike and modal stall phenomena in a low-speed axial compressor. ASME J Turbomach 1998; 120: 393–401.

. Role of tip clearance flow on axial compressor stability[D], Massachusetts Institute of Technology, 2001.

Weichert

Day

. Detailed measurements of spike formation in an axial compressor. J Turbomach 2014; 136: 051006–051006.

Marcel S, Stefan B and Reinhard N. Rotating stall inception inside the low pressure compressor of a twin-spool turbofan engine. In: Proceedings of ASME Turbo Expo 2013, USA, paper no, GT2013-94220.

McDougall

Cumpsty

Hynes

. Stall inception in axial compressor. ASME J Turbomach 1990; 112: 116–125.

10.

J-L

Chu

Peng

. Numerical and experimental research of stall inception on subsonic axial-flow compressor rotor. Proc. IMechE, Part G: J Aerospace Eng 2010; 224: 1027–1039.

11.

Furukawa

Inoue

Saiki

. The role of tip leakage vortex breakdown in compressor rotor aerodynamics. ASME J Turbomach 1999; 121: 469–480.

12.

Furukawa M, Saiki K, Yamada K, et al. Unsteady flow behavior due to breakdown of tip leakage vortex in an axial compressor rotor at neal-stall condition. ASME paper no. 2000-GT-666, 2000.

13.

Shengfeng

Xingen

Junqiang

. Effects of low Reynolds number on flow stability of a transonic compressor. Proc. IMechE, Part G: J Aerospace Eng 2015; 229: 601–611.

14.

Mailach R, Lehmann I and Vogeler K. Rotating instabilities in an axial compressor originating from the fluctuating blade tip vortex. ASME Paper no. 2000-GT-506, 2000.

15.

Maerz

Hah

Neise

. An experimental and numerical investigation into the mechanism of rotating instability. ASME J Turbomach 2002; 124: 367–374.

16.

Chen

Y-Y

Liu

Xuan

. A study of speed ratio affecting the performance of a contra-rotating axial compressor. Proc. IMechE, Part G: J Aerospace Eng 2008; 222: 985–991.

17.

Jermy

. Location of the vortex formation threshold at suction inlets near ground planes by computational fluid dynamics simulation. Proc. IMechE, Part G: J Aerospace Eng 2008; 222: 393–402.

18.

Junqiang

Zhiwei

Jun

. A new comprehension on stator cascade under rotating stall[J]. J Aerospace Power 1994; 9: 20–24.

19.

Chen

P-P

Qiao

W-Y

Hashmi

SFA

. Passive control of hub-corner separation/stall using axisymmetric-hub contouring. Proc. IMechE, Part G: J Aerospace Eng 2012; 226: 1214–1224.

20.

XianJun

BaoJie

ZhiBo

. Three-dimensional flow structures in stator passage of an axial compressor at the near-stall condition[J]. J Eng Thermophys 2009; 30: 53–56.

21.

XiaoXu

HuaWei

JingJun

. Study of influence on the rotor wake to the unsteady separation structure on transonic compressor stator[J]. J Eng Thermophys 2015; 36: 744–751.

22.

Zhongyue H and Xiaofang W. Turbocompressor[M]. Chemical Indus Press 2004; 1: 183–185.

23.

Ainley

. The performance of axial flow turbines[J]. Proc Instn Mech Engrs 1948; 156: 230–237.

24.

Horlock

. Axial flow turbines[M]. Int J Mech Sci 1966; 8(10): 651–652.

25.

Dajun Y and Zhongqin W. Study of real flow loss mechanism and control methods in tnrbomachinery [J].The Major Projects of the National Natural Science Foundation “The Key Issues in the Engineering Thermal Physics” Part I: Academic Study Concluded, 1992.

26.

Hawthorne WR. Some formulate for the calculation of secondary flow in cascades[R].ARC Report no. 17519, 1955.

27.

JingJun

HaiYang

Peng

. Numerical study of flow-field in compressor stator with inlet total pressure distortion[J]. J Eng Thermophys 2013; 34: 1234–1238.

28.

HuaWei

Shuang

JingJun

. Investigation of flow structure in compressor stator passage with hub tip [J]. J Eng Thermophys 2012; 33: 51–54.

29.

Shun

Zhongqi

. Application of topological analysis to studying the three-dimensional flow in cascades; part i. topological rules for skin-friction lines and section streamlines. Appl Math Mech 1990; 11: 489–495.