Comparison of Piezoelectric Energy Harvesting Devices for Recharging Batteries

Abstract

Piezoelectric materials can be used as a means of transforming ambient vibrations into electrical energy that can then be stored and used to power other devices. With the recent surge of microscale devices, piezoelectric power generation can provide a convenient alternative to traditional power sources used to operate certain types of sensors/actuators, telemetry, and MEMS devices. However, the energy produced by these materials is in many cases far too small to directly power an electrical device. Therefore, much of the research into power harvesting has focused on methods of accumulating the energy until a sufficient amount is present, allowing the intended electronics to be powered. In a recent study by Sodano et al. (2004a) the ability to take the energy generated through the vibration of a piezoelectric material was shown to be capable of recharging a discharged nickel metal hydride battery. In the present study, three types of piezoelectric devices are investigated and experimentally tested to determine each of their abilities to transform ambient vibration into electrical energy and their capability to recharge a discharged battery. The three types of piezoelectric devices tested are the commonly used monolithic piezoceramic material lead–zirconate–titanate (PZT), the bimorph Quick Pack (QP) actuator, and the macro-fiber composite (MFC). The experimental results estimate the efficiency of the three devices tested and identify the feasibility of their use in practical applications. Different capacity batteries are recharged using each device, to determine the charge time and maximum capacity battery that can be charged. The results presented in this article provide a means of choosing the piezoelectric device to be used and estimate the amount of time required to recharge a specific capacity battery.

Keywords

power harvesting energy scavenging piezoelectric macro-fiber composite MFC self-powered

References

Elvin, N. , Elvin, A. and Choi, D.H. 2003. ‘A Self-Powered Damage Detection Sensor,’ Journal of Strain Analysis for Engineering Design, 38(2): 115–124 .

Hausler, E. and Stein, E. 1984. ‘Implantable Physiological Power Supply with PVDF Film,’ Ferroelectrics, 60: 277–282 .

Hofmann, H. , Ottman, G.K. and Lesieutre, G.A. 2002. ‘Optimized Piezoelectric Energy Circuit Using Step-Down Converter in Discontinuous Conduction Mode,’ IEEE Transactions on Power Electronics, 18(2): 696–703 .

Kasyap, A. , Lim, J. , Johnson, D. , Horowitz, S. , Nishida, T. , Ngo, K. , Sheplak, M. and Cattafesta, L. 2002. ‘Energy Reclamation from a Vibrating Piezoceramic Composite Beam,’ In: Proceedings of 9th International Congress on Sound and Vibration, Orlando, FL, Paper No. 271.

Kimura, M. 1998. ‘Piezoelectric Generation Device,’ United States Patent Number 5,801,475-475.

Kymissis, J. , Kendall, D. , Paradiso, J. and Gershenfeld, N. 1998. ‘Parasitic Power Harvesting in Shoes,’ In: Second IEEE International Conference on Wearable Computing, August, pp. 132–336 .

Ottman, G.K. , Hofmann, H. , Bhatt, C.A. and Lesieutre, G.A. 2002. ‘Adaptive Piezoelectric Energy Harvesting Circuit for Wireless, Remote Power Supply,’ IEEE Transactions on Power Electronics, 17(5): 1–8 .

Ramsey, M.J. and Clark, W.W. 2001. ‘Piezoelectric Energy Harvesting for Bio MEMS Applications,’ In: Proceedings of SPIE's 8th Annual Smart Materials and Structures Conference, Vol. 4332, Newport Beach, CA, pp. 429–438 .

Starner, T. 1996. ‘Human-Powered Wearable Computing,’ IBM Systems Journal, 35: 618–629 .

10.

Sodano, H.A. , Inman, D.J. and Park, G. 2004a. ‘Generation and Storage of Electricity from Power Harvesting Devices,’ Journal of Intelligent Material Systems and Structures, 16(1), pp. 67–75 .

11.

Sodano, H.A. , Park, G. and Inman, D.J. 2004b. ‘Estimation of Electric Charge Output for Piezoelectric Energy Harvesting,’ Journal of Strain, 40(2): 49–58 .

12.

Sodano, H.A. , Park, G. and Inman, D.J. 2004c. ‘A Review of Power Harvesting from Vibration using Piezoelectric Materials,’ The Shock and Vibration Digest, 36(3): 197–205 .

13.

Sodano, H.A. , Lloyd, J. and Inman, D.J. 2004d. ‘An Experimental Comparison between Several Active Composite Actuators for Power Generation,’ In: Proceedings of SPIE's 11th Annual International Symposium on Smart Structures and Materials, San Diego, CA, March 14–18, Vol. 5390, pp. 370–378 .

14.

Umeda, M. , Nakamura, K. and Ueha, S. May 1996. ‘Analysis of Transformation of Mechanical Impact Energy to Electrical Energy Using a Piezoelectric Vibrator,’ Japanese Journal of Applied Physics, Part 1, 35(5B): 3267–3273 .

15.

Umeda, M. , Nakamura, K. and Ueha, S. 1997. ‘Energy Storage Characteristics of a Piezo-Generator Using Impact Induced Vibration,’ Japanese Journal of Applied Physics, Part 1, 35(5B): 3146–3151 .

16.

Wilkie, W.K. , Bryant, R.G. , High, J.W. , Fox, R.L. , Hellbaum, R.F. , Jalink, A. , Little, B.D. and Mirick, P.H. 2000. ‘Low-Cost Piezocomposite Actuator for Structural Control Applications,’ In: Proceedings of SPIE's 7th International Symposium on Smart Structures and Materials, Newport Beach, CA, March 5–9, Vol. 3991, pp. 323–334 .

17.

Williams, B.R. , Park, G. , Inman, D.J. and Wilkie, W.K. 2002. ‘An Overview of Composite Actuators with Piezoceramic Fibers,’ In: Proceedings of 20th International Modal Analysis Conference, Los Angeles, CA, February 4–7, Vol. 4753, pp. 421–427 .