A Comparison of Dynamic Piezoactuation of Fiber-based Actuators and Conventional PZT Patches

Abstract

This work aims to extend investigations of the dynamic flexural actuation of a cantilever beam to fiber-based actuators (e.g., active fiber composite (AFC) or macro-fiber composite (MFC)), which consist of a single level of unidirectionally aligned piezoceramic fibers surrounded by a polymer matrix and electrically loaded by interdigitated electrodes. The main advantage of such actuators is their poling in the same direction as the beam length, i.e., they are able to act with the piezoelectric strain constant d ₃₃ that is about two times higher than the piezoelectric strain constant d ₃₁ used in PZT patches. Modeling using the finite element method is based on the multiplication in both plane directions of a unit cell, which is taken as a fiber unit (with its matrix) within two pairs of half-electrodes of the same polarity. Modeling of the whole system is possible practically only with MFC actuators, whose fibers have a rectangular section, thus reducing the number of required finite elements. In addition to a non-uniform longitudinal free extension of the electrically loaded piezofiber-based actuator, a lateral free shearing has been calculated, which results in a non-planar deformation of the actuator. When two such MFC actuators are bonded on both sides of an aluminum cantilever beam and loaded in the antiphase mode, they conduct into all flexural resonance modes of the actuated beam, as expected. However, a slight interference by the torsion eigenmodes of the actuated beam has also been detected, which was not present in the actuation type using (leadzirconate titanate) PZT patches. The experimental validation of these FEM results first confirms the static values for free strain components of the MFC actuator depending on the loading voltage, then dynamic values regarding the eigenfrequencies, as well as the acceleration amplitudes of the MFC actuated vibrating beam.

Keywords

dynamic piezoactuation fiber-based actuator active fiber composite AFC macro-fiber composite MFC PZT

References

Belloli, A. , Castelli, B. , Kornmann, X. , Huber, C. and Ermanni, P. 2004. “Modeling and Characterization of Active Fiber Composites,” In: Flatau, A.B. (ed.), Proc. SPIE, Smart Structures and Materials 2004: Smart Structures and Integrated Systems, Vol. 5390, pp. 78–88, San Diego, CA, July 2004.

Bent, A. and Hagood, N.W. 1997. “Piezoelectric Fiber Composites with Interdigitated Electrodes,” J. Intell. Mater. Syst. and Structures. 8(11):903–919.

Crawley, E.F. and de Luis, J. 1987. “Use of Piezoelectric Actuators as Elements of Intelligent Structures,” AIAA Journal, 25(10): 1373–1385.

Crawley, E.F. and Anderson, E.H. 1990. “Detailed Models of Piezoceramic Actuation of Beams,” J. of Intell. Mater. Syst. and Struct., 1(4):4–25.

French, J.D. , Weitz, G.E. , Luke, J.E. , Cass, R.B. , Jadidian, B. , Bhargava, P. and Safari, A. 1997. “Production of Continuous Piezoelectric Ceramic Fibers for Smart Materials and Active Control Devices,” In: Sater, J.M. (ed.), Proc. SPIE, Smart Structures and Materials 1997: Industrial and Commercial Applications of Smart Structures Technologies, Vol. 3044, pp. 406–412, San Diego, CA, May 1997.

Fuller, C.R. , Elliott, S.J. and Nelson, P.A. 1996. Active Control of Vibration, Academic Press, London.

Gibbs, G.P. and Fuller, C.R. 1992. “Excitation of Thin Beams using Asymmetric Piezoelectric Actuators,” Journal of the Acoustical Society of America, 92(6):3221–3227.

Hwang, W.S. and Park, H.C. 1993. “Finite Element Modeling of Piezoelectric Sensors and Actuators,” AIAA Journal, 5(31): 930–937.

Kim, S.J. , Hwang, J.S. and Paik, S.H. 2003. “Direct Numerical Simulation of Active Fiber Composite,” In: Lagoudas, D.C. (ed.), Proc. SPIE, Smart Structures and Materials 2003: Active Materials, Behavior and Mechanics, Vol. 5053, pp. 568–575, San Diego, CA, August 2003.

10.

Kornmann, X. and Huber, C. 2004. “Microstructure and Mechanical Properties of PZT Fibers,” J. Eur. Ceram. Soc., 24(7):1987–1991.

11.

Nguyen, C.H. and Pietrzko, S.J. 2002. “Analytical and FEMInvestigations with Experimental Validation of a PZT-Actuated Vibrating Beam and its Sound Vibration,” In: Proc. ISMA2002, Int. Conf. on Noise and Vibration Engineering, Leuven, Sept. 16–18, 2002.

12.

Nguyen, C.H. and Pietrzko, S.J. 2004. “Piezoelectric-Mechanical-Acoustic Couplings from a PZT-Actuated Vibrating Beam and its Sound Vibration,” Mechanical Systems and Signal Processing, 18(4):929–945.

13.

Nguyen, C.H. , Pietrzko, S.J. and Buetikofer, R. 2004. “Influence of Temperature and Bonding Thickness on the Actuation of a Cantilever Beam by PZT-Patches,” Smart Materials and Structures, 13(4):851–860.

14.

Rogers, J. and Hagood, N. 1995. “Manufacture of Adaptive Composite Plates Incorporating Piezoelectric Fiber Composites Plies,” In: AIAA Paper 95-1096-CP, 36th AIAA/ASME/ASCE/AHS/ASC Structures, Dynamics, and Materials Conference, New Orleans, LA, April 10–13, 1995.

15.

Sodano, H.A. , Park, G. and Inman, D.J. 2004. “An Investigation into the Performance of Macro-Fiber Composites for Sensing and Structural Vibration Applications,” Mechanical Systems and Signal Processing, 18(3):683–697.

16.

Strock, H.B. , Pascucci, M.R. , Parish, M.V. , Bent, A.A. and Shrout, T.R. 1999. “Active PZT Fibers, A Commercial Production Process,” In: Wultig, M.R. (ed.), Proc. SPIE, Smart Structures and Materials 1999: Smart Materials Technologies, Vol. 3675, pp. 22–31, Newport Beach, CA, July 1999.

17.

Wickramasinghe, V.K. and Hagood, N.W. 2004. “Material Characterization of Active Fiber Composites for Integral Twist-Actuated Rotor Blade Application,” Smart Materials and Structures, 13(5):1155–1165.

18.

Wilkie, W.K. , Bryant, R.G. , High, J.W. , Fox, R.L. , Hellbaum, R.F. , Jalink, A. , Little, B.D. and Mirick, P.H. 2000. “Low-Cost Piezocomposite Actuator for Structural Control Applications,” In: Jacobs, J.H. (ed.), Proc. SPIE, Smart Structures and Materials 2000: Industrial and Commerical Applications of Smart Structures Technologies, Vol. 3991, pp. 323–333, Newport Beach, CA, June 2000.

19.

Williams, B.R. 2004. “Nonlinear Mechanical and Actuation Characterization of Piezoceramic Fiber Composites,” PhD Dissertation, Virginia Polytechnic and State University, March 2004.

20.

Williams, B.R. , Park, G. , Inman, D.J. and Wilkie, W.K. 2002. “An Overview of Composite Actuators with Piezoceramic Fibers,” In: Proc. of 20th Int. Modal Analysis Conference, Los Angeles, CA, Feb. 4–7, 2002.

21.

Williams, B.R. , Inman, D.J. , Schultz, M.R. , Hyer, M.W. and Wilkie, W.K. 2004. “Nonlinear Tensile and Shear Behavior of Macro Fiber Composite Actuators,” J. of Composite Materials, 38(10):855–869.