Heat and Mass Transfer in Polyurethane Insulated District Cooling and Heating Pipes

Abstract

The heat and mass transfer in PUR insulated pipes used for dis trict cooling and district heating is studied. During the aging of the pipes, the blowing agent, in this study CO₂ for the PUR foam will diffuse out through the casing and air components will diffuse into the foam. This diffusion will deterio rate the thermal properties of the insulation foam. For district cooling pipes, in ward diffusion and condensation of water vapor may occur which may increase the risk for corrosion, change the thermal properties, and affect leakage alarms. Theo retical models for mass and heat transfer are developed and solved numerically. The importance of the quality of the casing, the insulation thickness, the wall thickness of the casing, and the surrounding temperature is studied. Results for the diffusion process, thermal conductivity, and amount of condensed water are presented. The quality of the casing has a vital importance on the diffusion process. With a higher density of the casing, the diffusion process will be slower and the deterioration of the thermal properties become slower. The surrounding temperature, the insula tion thickness, and wall thickness of the casing are also of great importance. The amount of condensed water in the PUR foam is found to be very small during a pe riod of thirty years and will hardly affect the thermal performance or the leakage alarms.

Keywords

district cooling pre-insulated diffusion CO2 water vapor con densation thermal conductivity.

References

F.P. Incropera and D.P. DeWitt , Fundamentals of Heat and Mass Transfer, 4th ed., Wiley, New York, 1996.

D.W. Van Krevelen , Properties of Polymers, Elsevier, Amsterdam,1990, chapter 18.

K. Brodt , Thermal Insulations: cfc-alternatives and vacuum insulation, Thesis, Techmsche Universiteit Delft, Haag, 1995.

J Crank and G.S. Park , Diffusion in Polymers, Academic Press, London, 1968, pp. 274-276.

J. Brandrup and E.H. Immergut , Polymer Handbook, Wiley, New York , 1989, p. VI/437.

M. Svanstrom , Blowing Agents in Rigid Polyurethane Foam, Thesis, Chalmers University of Technology, Goteborg, Sweden, 1997

U. Jarfelt , Thermal Conductivity and Gas Diffusion of Rigid PUR foam, CFC-Free Polyurethane Research, Report No. 7, Part 2, Chalmers University of Technology, Goteborg, 1995.

U Jarfelt , Thermal Conductivity and Gas Diffusion of Rigid PUR foam, CFC-Free Polyurethane Research, Report No. 4, Part 1, Chalmers University of Technology, Goteborg, 1993.

Catalogue of Material Properties, Annex XIV, Vol. 3, Belgium, KU Leuven, 1991.

10.

P. Randlöv , District Heating Handbook, European District Heating Pipe Manufacturers Association (EuHP), Fredrica, Denmark, 1997.

11.

R.C. Reid and T.K. Sherwood , The Properties of Gases and Liquids, 2nd ed., McGraw-Hill, New York, 1968, pp. 481-490.

12.

P. Wan and L. Vamling , Thermal Conductivity of Gaseous Mixtures in Foams, CFC-Free Polyurethane Research , Report No. 3, Chalmers University of Technology, Goteborg, 1992.

13.

E.W. Behrens , G. Sirdeshpande and H.P. Woss , Closed-Cell Elastomeric Foams as Water-Vapor-Retardant Insulators on Cold Pipes, J. Thermal Insul. and Bldg Envs, Vol 16, 33-49, July 1992 .

14.

H.K. Versteeg and W Malalasekera, An Introduction to Computional Fluid Dynamics, Longman, Harlow, 1995, Chapter 4.

15.

S V. Patankar, Numerical Heat Transfer and Fluid Flow, Hemisphere , New York, 1980, Chapters 3 and 4.