Performance of alumina coatings prepared by hard anodizing,micro arc oxidation and detonation spray processes on Al–Mg–Si alloy under fretting wear loading
Restricted accessResearch articleFirst published online April, 2014
Performance of alumina coatings prepared by hard anodizing,micro arc oxidation and detonation spray processes on Al–Mg–Si alloy under fretting wear loading
Hard anodizing, micro arc oxidation and detonation spraying of alumina were done on AA 6063 substrate. Fretting wear tests were done at different normal loads and a constant displacement of 55 µm for 50,000 cycles at 5 Hz. The micro arc oxidation and detonation spray coated samples exhibited lower coefficient of friction compared to hard anodizing coated and uncoated samples. Both micro arc oxidation and detonation sprayed samples showed superior fretting wear resistance compared to hard anodizing and uncoated samples. However, hard anodizing coated samples exhibited inferior fretting wear resistance compared to uncoated samples due to cracking and fragmentation of brittle and hard anodized layer.
NishidaTMiztunaiJMutohYEffect of lubricating anodic film on fretting fatigue strength of aluminum alloy. In: MutohYKinyonSEHoeppnerDW (eds). ASTM STP 1425, West Conshohocken, PA, USA: ASTM, 2003, pp. 369–385.
2.
BrittMGabelBethkeJ. Coatings for fretting prevention. Wear1978; 46(1): 81–96.
3.
BraceA. Anodizing – its development, status, and future challenges. Met Finish2002; 100(11–12): 59–60.
4.
LopezVGonzalezJAOteroE. Atmospheric corrosion of bare and anodised aluminium in a wide range of environmental conditions. Part II: Electrochemical responses. Surf Coat Technol2002; 153(2–3): 235–244.
5.
Fratila-apachiteiLEDuszezykJKatgermanL. AlSi(Cu) anodic oxide layers formed in H2SO4 at low temperature using different current waveforms. Surf Coat Technol2003; 165(3): 232–240.
6.
VoevodinAAYerokhinALLyubimovVV. Characterization of wear protective Al–Si–O coatings formed on Al-based alloys by microarc discharge treatment. Surf Coat Technol1996; 86–87(2): 516–521.
NieXLeylandASongHW. Thickness effects on the mechanical properties of micro-arc discharge oxide coatings on aluminium alloy. Surf Coat Technol1999; 116–119(1): 1055–1060.
9.
XueWDengZChenR. Growth regularity of ceramic coatings formed by microarc oxidation on Al–Cu–Mg alloy. Thin Solid Films2000; 372(1–2): 114–117.
10.
Rama KrishnaLSomarajuKRCSundararajanG. The tribological performance of ultra-hard ceramic composite coatings obtained through microarc oxidation. Surf Coat Technol2003; 163–164(1): 484–490.
11.
McCollIRHarrisSJHuQ. Influence of surface and heat treatment on the fretting wear of an aluminium alloy reinforced with SiC particles. Wear1997; 203–204(1): 507–515.
12.
DearnleyPAGummersbachJWeissH. The sliding wear resistance and frictional characteristics of surface modified aluminium alloys under extreme pressure. Wear1999; 225–229(1): 127–134.
13.
Rama KrishnaLSudha PurnimaASundararajanG. A comparative study of tribological behaviour of microarc oxidation and hard-anodized coatings. Wear2006; 261(10): 1095–1101.
14.
RameshRGnanamoorthyR. Development of a fretting wear test rig and preliminary studies for understanding the fretting wear properties of steels. Mater Des2006; 27(2): 141–146.
15.
KalinMVizintinJ. Use of equations for wear volume determination in fretting experiments. Wear2000; 237(1): 39–48.
16.
RajasekaranBGanesh Sundara RamanSRama KrishnaL. Influence of microarc oxidation and hard anodizing on plain fatigue and fretting fatigue behaviour of Al–Mg–Si alloy. Surf Coat Technol2008; 202(8): 1462–1469.
17.
RajasekaranBGanesh Sundara RamanSJoshiSV. Influence of detonation gun sprayed alumina coating on AA 6063 samples under cyclic loading with and without fretting. Tribol Int2008; 41(4): 315–322.
18.
ZhangYSHanZLuK. Fretting wear behaviour of nanocrystalline surface layer of copper under dry condition. Wear2008; 265(3–4): 396–401.
19.
ZmitrowiczA. Wear debris: A review of properties and constitutive models. J Theor Appl Mech2005; 43(1): 3–35.
20.
VarenbergMHalperinGEtsionI. Different aspects of the role of wear debris in fretting wear. Wear2002; 252(11–12): 902–910.
21.
WartburtonJ. The fretting of mild steel in air. Wear1989; 131(2): 365–386.
22.
IwabuchiA. The role of oxide particles in the fretting wear of mild steel. Wear1991; 151(2): 301–311.
23.
LiuHWXuXJZhuMH. High temperature fretting wear behaviour of WC–25Co coatings prepared by D-gun spraying on Ti–Al–Zr titanium alloy. Tribol Int2011; 44(11): 1461–1470.
24.
VingsboOSoderbergS. On fretting maps. Wear1988; 126(2): 131–147.
25.
KapoorAFranklinFJ. Tribological layers and the wear of ductile materials. Wear2000; 245(1–2): 204–215.
