The creep rupture properties of AISI 347 austenitic stainless steel foil used in compact recuperators have been evaluated at 750 ℃ in the stress range of 54–221 MPa to establish baseline behavior for its extended use. The creep curve of the foil shows that the primary creep stage is brief and creep life is dominated by tertiary creep deformation with rupture lives in the range 3–433 h. Power law relationship was obtained between the minimum creep rate and the applied stress with stress exponent value of n = 4.25. The creep damage tolerance parameter for specimen tested at 750 ℃ and 54 MPa indicates that creep fracture takes place by precipitate coarsening mechanism. Nucleation of voids mainly occurs at second-phase particles (Cr23C6 carbides). The improvement in strength is attributed to the precipitation of fine niobium carbides in the matrix which prevents dislocation movement of the microstructure.
GarcíaJCastilloMRodríguezSet al.Carbide precipitation study in a high heat resistance austenitic stainless steel HK40. MRS Online Proceedings Library2010. DOI: 10.1557/PROC-1275-S3-P24.
2.
KawasakiTChiMH. Analysis of accelerated creep under constant sustaining load for austenitic stainless steels. Metall Trans A1979; 10: 749–757.
3.
LahaKKyonoJShinyaN. Copper, boron, and cerium additions in type 347 austenitic steel to improve creep rupture strength. Metall Mater Trans A2012; 43: 1187–1197.
4.
NassourABoseWWSpinelliD. Creep properties of austenitic stainless-steel weld metals. J Mater Eng Perform2001; 10: 693–698.
5.
MinamiYKimuraHIharaY. Microstructural changes in austenitic stainless steels during long-term aging. Mater Sci Technol1986; 2: 795–806.
6.
SourmailT. Precipitation in creep-resistant austenitic stainless steels. Mater Sci Technol2001; 17: 1–14.
7.
LahaKKyonoJSasakiTet al.Improved creep strength and creep ductility of Type 347 austenitic stainless steel through the self-healing effect of bron for creep cavitation. Metall Mater Trans A2005; 36: 399–409.
8.
ShinyaNKyonoJLahaK. Self-healing effect of boron nitride precipitation on creep cavitation in austenitic stainless steels. J Intell Mater Syst Struct2006; 17: 1127–1133.
9.
ShinyaNKyonoJLahaK. An advanced creep cavitation resistance in Cu-containing 18Cr-12Ni-Nb austenitic stainless steels. Scripta Mater2007; 56: 915–918.
10.
LahaKKyonoJShinyaN. Some chemical and microstructural factors influencing creep cavitation resistance of austenitic stainless steels. Philos Mag2007; 87: 2483–2505.
11.
AvnerSH. Introduction to physical metallurgy, 1st ed. New York: McGraw-Hill International, 1974.
12.
ASTM E139:2000. Standard test methods for conducting creep, creep-rupture and stress rupture tests of metallic materials, West Conshohocken, PA: ASTM, 2000.
13.
Maziasz PJ, Swindeman RW, Shingledecker JP, et al. Improving high-temperature performance of austenitic stainless steels for advanced microturbine recuperators. In: Engineering issues in turbine machinery, power plants and renewables, Proceedings of the sixth international Charles Parsons turbine conference, Trinity College Dublin, Ireland, 16–18 September 2003, pp.1057–1073.
14.
Mathew MD, Latha S, Mannan SL, et al. Creep rupture properties of solution annealed and cold worked type 316 stainless steel cladding tubes. Report for the Indira Gandhi Centre for Atomic Research, India, 1990.
15.
EvansRWWilshireB. Introduction to creep, London: The Institute of Materials, 1993, pp. 62–62.
16.
MorrisDGHarriesDR. Creep and rupture in type 316 stainless steel at temperatures between 525 and 900 ℃, part I: Creep rate. Metal Sci1978; 12: 542–549.
17.
MannanSLRodriguezP. Effect of grain size on creep rate in type 316 stainless steel at 873 and 973 K. Metal Sci1983; 17: 63–69.
18.
MathewMDSasikalaGRaoKBSet al.Influence of carbon and nitrogen on the creep properties of type 316 stainless steel at 873 K. Mater Sci Eng A1991; 148: 253–260.
19.
FrostHJAshbyMF. Deformation-mechanism maps: The plasticity and creep of metals and ceramics, Oxford: Pergamon, 1982.
20.
KesternichWMeertensD. Microstructural evolution of a titanium stabilized 15Cr–15Ni steel. Acta Metall1986; 34: 1071–1082.
21.
Brown LM and Embury JD. The initiation and growth of voids at second-phase particles. In: Proceedings of the 3rd international conference on strength of metals and alloys, 1973, pp.164–169. London: Institute of Metals.
22.
PuttickKE. Ductile fracture in metals. Philos Mag1959; 4: 964–969.
23.
ArgonASImJ. Separation of second phase particles in spheroidized 1045 steel, Cu - 0.6% Cr alloy, and maraging steel in plastic straining. Metall Trans A1975; 6: 839–851.
