To assess the effectiveness of the near surface mounted (NSM) technique, in terms of load carrying and moment redistribution capacities, for the flexural strengthening of continuous reinforced concrete (RC) slabs, an experimental program was carried out. The experimental program is composed of three series of three slab strips of two equal span length, in order to verify the possibility of increasing the negative (at the intermediate support region) resisting bending moment in 25% and 50% and maintaining moment redistribution levels of 15%, 30% and 45%. Though the flexural resistance of the NSM strengthened sections has exceeded the target values, the moment redistribution was relatively low, and the increase of the load carrying capacity of the strengthened slabs did not exceed 25%. This experimental program is analyzed to highlight the possibilities of NSM technique for statically indeterminate RC slabs in terms of flexural strengthening effectiveness, moment redistribution and ductility performance. Using a FEM-based computer program, which predictive performance was appraised using the obtained experimental results, a high effective NSM flexural strengthening strategy is proposed, capable of enhancing the slab's load carrying capacity and maintaining high levels of ductility.
ACI Committee 318 (2004). ACI 318–04: Building Code Requirements for Structural Concrete and Commentary, American Concrete Institute, Detroit, USA.
2.
ACI Committee 440 (2007). ACI 440: Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, American Concrete Institute, Detroit, USA.
3.
ArduiniM.TommasoD.A. and NanniA. (1997). “Brittle failure in FRP plate and sheet bonded beams”, ACI Structural Journal, Vol. 94, No. 4, pp. 363–370.
4.
AshourS.A. (2000). “Effect of compressive strength and tensile reinforcement ratio on flexural behavior of high-strength concrete beams”, Engineering Structures, Vol. 22, No. 5, pp. 413–423.
5.
AshourA.F.El-RafaieS.A. and GarrityS.W. (2004). “Flexural strengthening of RC continuous beams using CFRP laminates”, Cement and Concrete Composites, Vol. 26, No. 7, pp. 765–775.
6.
ASTM 370 (2002). Standard Test Methods and Definitions for Mechanical Testing of Steel Products, American Society for Testing and Materials, West Conshohocken, PA, USA.
7.
ASTM D3039 (1993). Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, American Society for Testing and Materials, West Conshohocken, PA, USA.
8.
BarrosJ.A.O.DalfréG.M. and DiasJ.P. (2008). “Numerical simulation of continuous RC slabs strengthened using NSM technique”, Proceedings of 2nd International Conference on Concrete Repair, Rehabilitation and Retrofitting, Cape Town, South Africa, November.
9.
BarrosJ.A.O. and FortesA.S. (2005). “Flexural strengthening of concrete beams with CFRP laminates bonded into slits”, Cement and Concrete Composites, Vol. 27, No. 4, pp. 471–480.
10.
BarrosJ.A.O.DiasS.J.E. and LimaJ.L.T. (2007). “Efficacy of CFRP-based techniques for the flexural and shear strengthening of concrete beams”, Cement and Concrete Composites, Vol. 29, No. 3, pp. 203–217.
11.
BarrosJ.A.O. and FigueirasJ.A. (2001). “Model for the analysis of steel fibre reinforced concrete slabs on grade”, Computers & Structures, Vol. 79, No. 1, pp. 97–106.
12.
BlaschkoM. and ZilchK. (1999). “Rehabilitation of concrete structures with CFRP strips glued into slits”, Proceedings of 12th International Conference on Composite Materials, Paris, France, July.
13.
BonaldoE. (2008). Composite Materials and Discrete Steel Fibres for the Strengthening of Thin Concrete Structures, PhD Thesis, University of Minho, Guimarães, Portugal.
14.
BonaldoE.BarrosJ.A.O. and LourençP.J.B. (2008). “Efficient strengthening technique to increase the flexural resistance of existing RC slabs”, Journal of Composites for Construction, ASCE, Vol. 12, No. 2, pp. 149–159.
15.
CasadeiP.NanniA.GalatiN.IbellT. and DentonS. (2003). “Moment redistribution in continuous CFRP-strengthened concrete members: Experimental results”, Proceedings of International Conference Composites in Construction (CCC2003), Cosenza, Italy, September.
16.
CEB-FIP Model Code 1990 (1993). Design Code, Thomas Telford, Lausanne, Switzerland.
17.
Concrete Society (2000). Design Guidance for Strengthening Concrete Structures Using Fibre Composite Materials, Concrete Society Technical Report No. 55, The Concrete Society, Century House, Telford Avenue, Crowthorne, Berkshire, UK.
18.
DalfréG.M. and BarrosJ.A.O. (2009a). Numerical Analysis of Two-Way RC Slabs Flexural Strengthened with NSM CFRP Laminates, Technical Report 09-DEC/E-09, Department of Civil Engineering, University of Minho, Portugal.
19.
DalfréG.M. and BarrosJ.A.O. (2009b). Movies of the SL15s25 Slab of the Second Group of the NSM Flexural Strengthened Continuous RC Slabs, Department of Civil Engineering, University of Minho, Portugal. (http://www.civil.uminho.pt/mrtest)
20.
El-HachaR. and RizkallaS.H. (2004). “Near-surface-mounted fiber-reinforced polymer reinforcements for flexural strengthening of concrete structures”, ACI Structural Journal, Vol. 101, No. 5, pp. 717–726.
21.
El-RefaieS.A.AshourA.F. and GarrityS.W. (2003a). “Sagging and hogging strengthening of continuous reinforced concrete beams using CFRP sheets”, ACI Structural Journal, Vol. 100, No. 4, pp. 446–453.
22.
El-RefaieS.A.AshourA.F. and GarrityS.W. (2003b). “CFRP strengthened continuous concrete beams”, Structures and Buildings, Vol. 156, No. 4, pp. 395–404.
23.
EN 1992-1-1 (2004). Eurocode 2: Design of Concrete Structures-Part 1–1: General Rules and Rules for Buildings, CEN, Brussels, Belgium.
24.
Fédération Internationale du Béton (FIB) (2001). Externally Bonded FRP Reinforcement for RC Structures, Bulletin 14, Lausanne, Switzerland.
25.
HassanT. and RizkallaS. (2003). “Investigation of bond in concrete structures strengthened with near surface mounted carbon fiber reinforced polymer strips”, Journal of Composites for Construction, ASCE, Vol. 7, No. 3, pp. 248–257.
26.
ISO 527–1 (1993). Plastics – Determination of Tensile Properties -Part 1: General Principles, International Organization for Standardization (ISO), Genèva, Switzerland.
27.
ISO 527–5 (1993). Plastics – Determination of Tensile Properties -Part 5: Test Conditions for Unidirectional Fibre-Reinforced Plastic Composites, International Organization for Standardization (ISO), Genèva, Switzerland.
28.
KotyniaR. (2006). “Analysis of reinforced concrete beams strengthened with near surface mounted FRP reinforcement”, Archives of Civil Engineering, Vol. 52, No. 2, pp. 305–317.
29.
LiuI.S.T.OehlersD.J.SeracinoR. and JuG. (2006a). “Moment redistribution parametric study of CFRP, GFRP and steel surface plated RC beams and slabs”, Construction and Building Materials, Vol. 20, No. 1–2, pp. 59–70.
30.
LiuI.S.T.OehlersD.J. and SeracinoR. (2006b). “Tests on the ductility of reinforced concrete beams retrofitted with FRP and steel near-surface mounted plates”, Journal of Composites for Construction, ASCE, Vol. 10, No. 2, pp. 106–114.
31.
NanniA.Di LudovicoM. and ParrettiR. (2004). “Shear strengthening of a PC bridge girder with NSM CFRP rectangular bars”, Advances in Structural Engineering, Vol. 7, No. 4, pp. 97–109.
32.
OehlersD.J.CampbellL.HaskettM.AntramP. and ByrneR. (2006). “Moment redistribution in RC beams retrofitted by longitudinal plating”, Advances in Structural Engineering, Vol. 9, No. 2, pp. 257–264.
33.
OehlersD.J.JuG.LiuI.S.T. and SeracinoR. (2004a). “Moment redistribution in continuous plated RC flexural members. Part1: Neutral axis depth approach and tests”, Engineering Structures, Vol. 26, No. 14, pp. 2197–2207.
34.
OehlersD.J.LiuI.S.T.JuG. and SeracinoR. (2004b). “Moment redistribution in continuous plated RC flexural members. Part2: Flexural rigidity approach”, Engineering Structures, Vol. 26, No. 14, pp. 2209–2218.
35.
ParkS.M. and OehlersD.J. (2000). Details of Tests on Steel and FRP Plated Continuous Reinforced Concrete Beams, Research Report R170, School of Civil and Environmental Engineering, University of Adelaide, Australia.
36.
Sena-CruzJ.M. (2004). Strengthening of Concrete Structures with Near-Surface Mounted CFRP Laminate Strips, PhD Thesis, Department of Civil Engineering, University of Minho, Guimarães, Portugal.
37.
StevensN.J. (1987). Analytical Modelling of Reinforced Concrete Subjected to Monotonic and Reversed Loadings, Publication No. 87–1, ISBN 0-7727-7088-3, University of Toronto, Canada.
38.
TäljstenB.CarolinA. and NordinH. (2003). “Concrete structures strengthened with near surface mounted reinforcement of CFRP”, Advances in Structural Engineering, Vol. 6, No. 3, pp. 201–213.
