International Journal of Aeroacoustics

Experimental investigation of Over-Tip-Rotor circumferential groove liners has shown potential for fan noise suppression in turbofan engines whilst providing minimal penalty in fan aerodynamic performance. The validation of Over-Tip-Rotor liner analytical prediction models against published experimental data requires the modelling of an equivalent impedance for such acoustic treatments. This paper describes the formulation of two analytical groove impedance models as semi-locally reacting liners, that is locally reacting in the axial direction and non-locally reacting in the azimuthal direction. The models are cross-verified by comparison with high-order FEM simulations, and applied to a simplified Over-Tip-Rotor configuration consisting of multiple grooves excited by a monopole point source located close to the grooved surface.

Metamaterials might be one of the breakthrough technologies needed from the aeronautic industry to achieve the more and more challenging targets set by the international authorities, especially about noise emissions. In this article, a theoretical link between Transformation Acoustics and Generalized Snell’s Law, two widely used metamaterial models, is demonstrated analytically and applied to case studies. The relevance of the connection in the aeroacoustic field is discussed along with the consequent computational advantages for numerical simulations. This is exploited to perform a simulation-based design optimization of a phase-graded metasurface acoustic lining of a 2 D duct in presence of flow. Results show promising abilities of the optimized device to modify and control the directivity of the noise emitted from the duct by means of unconventional reflections. The noise reduction in the desired direction is obtained through constructive and destructive interference, with no absorption from the boundaries.

The sound absorptive performance of a proposed “meta-liner” are investigated in this paper. The structure is composed of closely placed plates connected by openings at alternating locations in a stacked format. This system presents multiple band gaps with high absorption and sub-wavelength behaviour (sample thickness equals 0.04λ), achieved through tortuosity within the design. The acoustic response of the single layer is obtained numerically and with experimental verification under normal incidence. The repeating cellular design allows efficiencies in the viscothermal numerical analysis and using a transfer matrix approach, it is demonstrated that the response of the overall system may be efficiently predicted from a detailed model of a unit cell. Both the transfer matrix method and a full viscothermal model are validated against experimental data as a function of system depth. The analysis gives very satisfactory results which could form the basis for future designs.

Low-cost airlines have significantly increased air transport, thus an increase in aviation noise. Therefore, predicting aircraft noise is an important component for designing an aircraft to reduce its impact on environmental noise along with the cost of testing and certification. The aim of this work is to develop a three-dimensional Boundary Element Method (BEM), which can predict the sound propagation and scattering over metamaterials and metasurfaces in mean flow. A methodology for the implementation of metamaterials and metasurfaces in BEM as an impedance patch is presented here. A three-dimensional BEM named as BEM3D has been developed to solve the aero-acoustics problems, which incorporates the Fast Multipole Method to solve large scale acoustics problems, Taylor’s transformation to account for uniform and non-uniform mean flow, impedance and non-local boundary conditions for the implementation of metamaterials. To validate BEM3D, the predictions have been benchmarked against the Finite Element Method (FEM) simulations and experimental data. It has been concluded that for no flow case BEM3D gives identical acoustics potential values against benchmarked FEM (COMSOL) predictions. For Mach number of 0.1, the BEM3D and FEM (COMSOL) predictions show small differences. The difference between BEM3D and FEM (COMSOL) predictions increases further for higher Mach number of 0.2 and 0.3. The increase in difference with Mach number is because Taylor’s Transformation gives an approximate solution for the boundary integral equation. Nevertheless, it has been concluded that Taylor’s transformation gives reasonable predictions for low Mach number of up to 0.3. BEM3D predictions have been validated against experimental data on a flat plate and a duct. Very good agreement has been found between the measured data and BEM3D predictions for sound propagation without and with the mean flow at low Mach number.

In the framework of the German Collaborative Research Center CRC 880: Fundamentals of High Lift for Future Civil Aircraft porous materials as a means towards the reduction of airfoil trailing edge noise are investigated. At DLR, both experimental and numerical approaches are pursued to understand the physics behind the noise reduction. The present paper focuses on the numerical investigations, for which the experimental data serves as an evaluation basis. From the analysis of homogeneous materials, first steps are made towards the design of aeroacoustically tailored materials. It is assumed that materials with locally varying permeability may be suitable to achieve maximum noise reduction, as they provide a smooth transition from the solid airfoil to the free flow in the wake. The simulation results support this understanding, however it is revealed that high local gradients in the material properties themselves may act as acoustic sources.

The introduction of quiet short take-off and landing for civil aircraft operations in close proximity to the population poses important technological challenges. One critical aspect is the realization of extreme lift augmentation at low acoustic emissions. The aircraft concept selected to achieve this goal is a high-lift system equipped with an active flow-control non-slotted flap and a droop nose. For this specific configuration, trailing edge noise becomes a dominant noise source. Porous materials as a passive means for trailing-edge noise reduction are selected and characterized. Results of extensive experimental investigations in the acoustic wind tunnel Braunschweig are presented and discussed to point out the potential and limitations of the selected porous devices. Practical issues related to material manufacturing and integration into the wind tunnel model are addressed. The noise reduction potential of passive porous trailing-edge devices is found to strongly depend on both these aspects. Issues related to the characterization of the porous materials properties are described. Although porous materials are found to be successful at reducing trailing-edge noise emissions, the results indicate that there is still a need for more generic investigations to further clarify the parametric dependencies between noise reduction and material properties.