Waste Management & Research: The Journal for a Sustainable Circular Economy

The aims of this study were (i) to evaluate the performance of the composting process operation in full-scale mechanical-biological treatment (MBT) plants, (ii) to estimate their performance under optimized conditions and (iii) to propose specific guidelines on how to improve the efficiency of the composting process. To fulfil these objectives, a first-order kinetic model was used. This model was calibrated with experimental data to account for the limitations imposed by less-than-optimal environmental conditions during operation of the composting process. Data treatment and simulation showed that two of the three MBT plants studied were poorly operated. Optimization of process management with measures of simple practical implementation was estimated to be highly significant in these poorly managed plants, increasing performance by 103% in MBT1 and 53% in MBT2. In MBT3, the potential for optimization was estimated at 17%. Similar results were obtained from the analysis of other published data, suggesting that poor process management in MBT composting is widespread. These findings highlight the importance of having programmes for monitoring and optimizing process performance in full-scale composting systems. The procedures developed here are simple to apply and can routinely be implemented in full-scale plants.

To monitor the progress of organic matter degradation in a large-scale composting facility, the percentage of organic matter degradation was determined by measuring CO₂ evolution during recomposting of compost samples withdrawn from the facility. The percentage of organic matter degradation was calculated as the ratio of the amount of CO₂ evolved from compost raw material to that evolved from each sample during recomposting in the laboratory composting apparatus. It was assumed that the difference in the cumulative emission of CO₂ between the compost raw material and a sample corresponds to the amount of CO ₂ evolved from the sample in the composting facility. Using this method, the changes in organic matter degradation during composting in practical large-scale composting facilities were estimated and it was found that the percentage of organic matter degradation increased more vigorously in the earlier stages than in the later stages of composting. The percentage of organic matter degradation finally reached 78 and 55% for the compost produced from garbage—animal manure mixture and distillery waste (shochu residue), respectively. It was thus ascertained that organic matter degradation progressed well in both composting facilities. Furthermore, by performing a plant growth assay, it was observed that the compost products of both the facilities did not inhibit seed germination and thus were useful in promoting plant growth

In-vessel composting, a contribution to sustainable solid waste management, was conducted on source-separated waste materials generated in Abeokuta city, south-west Nigeria. Feedstock (household, agricultural and municipal waste) and the resultant composts were chemically characterized using standard procedures. Identification and changes in the microbial population during composting, the effects of composting on waste volume reduction (WVR) and elemental composition of composts were evaluated. Product performance on plant growth and metal uptake were then assessed using African spinach (Amaranthus hybridus) in a screen house for 8 weeks. Metals were determined in acid digest using atomic absorption spectrometry. Compost yields and WVR ranged from 35.28 to 48.68% and 51.66 to 64.72%, respectively. Compost heavy metal (Cu, Cr, Zn, Ni, Cd and Pb) concentrations (mg kg ^-1), ranging from 0.67—0.82; 0.13—7.5; 0.001—0.22; 1.67—18.33; 6.50—17.67; and 0.83—6.00 for Cu, Pb, Cd, Ni, Cr and Zn, respectively, were within limits for class A+ composts. The effect of composting varied with element type and significantly (p < 0.05) reduced microbial population by 44.44 to 88.46%. Plant height, leaf number and biomass yield gave positive correlations (r = 0.950 to 0.977; 0.978 to 0.989 and 0.99, respectively; p < 0.05) with applied compost rate. Low-metal composts were produced but the presence of Cd and Pb in plant tissues calls for further research on the long-term effect of products on plant metal uptake in amended soils. The study is a contribution to the data bank of composting as a low technology waste management option in the developing countries.

In the present study it was demonstrated that organic additives eluted from plastic resins could be utilized as substrates by sulfate-reducing bacteria. Two laboratory-scale experiments, a microcosm experiment and a leaching experiment, were conducted using polyvinyl chloride (PVC) as a model plastic resin. In the former experiment, the conversion of sulfate to sulfide was evident in microcosms that received plasticized PVC as the sole carbon source, but not in those that received PVC homopolymer. Additionally, dissolved organic carbon accumulated only in microcosms that received plasticized PVC, indicating that the dissolved organic carbon originated from additives. In the leaching experiment, phenol and bisphenol A were found in the leached solutions. These results suggest that the disposal of waste plastics in inert waste landfills may result in the production of H₂S.

Nitrification of mature sanitary landfill leachate with high-strength of N-NH₄ + (1080—2350 mg L^-1) was performed in a 10 L continuous nitrification activated sludge reactor. The nitrification system was acclimatized with synthetic leachate during feed batch operation to avoid substrate inhibition before being fed with actual mature leachate. Successful nitrification was achieved with an approximately complete ammonium removal (99%) and 96% of N-NH₄ + conversion to N-NO^- ₃ . The maximum volumetric and specific nitrification rates obtained were 2.56 kg N-NH₄ ⁺ m^-3 day^-1 and 0.23 g N-NH₄ ⁺ g^-1 volatile suspended solid (VSS) day^-1, respectively, at hydraulic retention time (HRT) of 12.7 h and solid retention time of 50 days. Incomplete nitrification was encountered when operating at a higher nitrogen loading rate of 3.14 kg N-NH₄ ⁺ m^-3 day^-1. The substrate overloading and nitrifiers competition with heterotrophs were believed to trigger the incomplete nitrification. Fluorescence in situ hybridization (FISH) results supported the syntrophic association between the ammonia-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria. FISH results also revealed the heterotrophs as the dominant and disintegration of some AOB cell aggregates into single cells which further supported the incomplete nitrification phenomenon.

Long-term behaviour of leachate pollutants is a key factor to estimate time and cost required for the leachate treatment in landfills. Estimating carbon release via leachate can be a good way by which to understand the long-term behaviour, however, most studies have had a timeline of only several months or years. In this study, a release rate of carbon via leachate for 20 years was estimated at an industrial solid waste landfill. The total carbon content in dumped waste was estimated based on combustible contents determined by collecting samples from other industrial landfills and pretreatment facilities, and carbon contents in literature values. Leachate quantity data, which were not recorded for the first ten years, were estimated using a macro-moisture balance model including the effect of snow melt. Because leachate quantity and quality at each site were only measured after leachates were mixed, the quantity at each site was calculated by assuming infiltration rates with and without final cover. Results indicated that less than 2% of total input carbon was released from each site via leachate regardless of landfill age.

The household appliance industry is one of the most important sectors from both the economic and environmental point of view. A greater understanding of the way in which consumers of these items behave would help to better plan the recycling needs as a function of previous purchase figures. This paper presents the findings of a field survey of Spanish consumer habits with respect to different common household appliances as regards replacement time and the reasons for replacing these appliances. The methodology used is based on survival analysis; specifically, a competing risks model. A Cox proportional hazards model is also used for the sake of comparison. Our results show that as the number of people and/or persons under 18 years in the household increases, the lifetimes of some types of appliance decrease significantly. Competing risk model shows that the probability of replacing the refrigerator due to malfunction and technological obsolescence increases with the increase of family members with a higher education. We also provide the cumulative incidence function for different appliances, which can be used to forecast future demands and electrical and electronic waste generation.

The waste management of a chlor-alkali and calcium chloride industrial facility from southern Chile was the object of this study. The main solid waste materials generated in these processes are brine sediments and calcium chloride sediments, respectively. Both residues are mixed in the liquid phase and filtered in a press filter, obtaining a final low humidity solid waste, called ‘mixed sediments’, which is disposed of in an industrial landfill as non-hazardous waste. The aim of the present study was to compare by means of LCA, the current waste management option of the studied chlor-alkali facility, namely landfill disposal, with two new possible options: the reuse of the mixed sediments as mineral additive in compost and the use of brine sediments as an unconventional sorbent for the removal of heavy metals from wastewater. The functional unit was defined as 1 tonne of waste being managed. To perform this evaluation, software SimaPro 7.0 was used, selecting the Ecoindicator 99 and CML 2000 methodologies for impact evaluation. The obtained results indicate that the use of brine sediments as a novel material for the removal of heavy metals from wastewater (scenario 3) presented environmental benefits when compared with the waste management option of sediments landfilling (scenario 1). The avoided environmental loads, generated by the substitution of activated granular carbon and the removal of Cu and Zn from wastewater in the treatment process generated positive environmental impacts, enhancing the environmental performance of scenario 3.

It is demonstrated that substantial reductions in plastics presently disposed of in landfills can be achieved by cyclone density media separation (DMS). In comparison with the size fraction of plastics presently processed by industrial density separations (generally 6.4 to 9.5 mm), cyclone DMS methods are demonstrated to effectively process a substantially greater range of particle sizes (from 0.5 up to 120 mm). The purities of plastic products and recoveries obtained with a single stage separation using a cylindrical cyclone are shown to attain virtually 100% purity and recoveries >99% for high-density fractions and >98% purity and recoveries were obtained for low-density products. Four alternative schemas of multi-stage separations are presented and analyzed as proposed methods to obtain total low- and high-density plastics fraction recoveries while maintaining near 100% purities. The results of preliminary tests of two of these show that the potential for processing product purities and recoveries >99.98% of both density fractions are indicated. A preliminary economic comparison of capital costs of DMS systems suggests cyclone DMS methods to be comparable with other DMS processes even if the high volume capacity for recycling operations of these is not optimized.

This paper presents an overview of mercury-containing lamp (MCL) recycling initiatives currently available in the world, especially in the United States. The majority of MCLs contain mercury which is a neurotoxin, a persistent pollutant in the environment, and can bioaccumulate in the food chain. Although there are some recycling options in the United States, collection rates are still at 23% of all potential used MCLs. This shows that citizens are either indifferent to or unaware of the recycling alternatives. On the other hand, MCL recycling seems not to be a cost-effective process and, for this reason, in the United States, take-back programmes are still sponsored only by consumers or municipalities. A few retailers have recently initiated limited take-back alternatives and manufacturers have not yet supported financially any consistent recycling alternative in the country. Considering successful experiences, this paper makes a suggestion for an MCL recycling system based on the concepts of extended producer responsibility and product stewardship. A manufacturer-importer advance recycling fee is proposed to finance the collection and recycling system while a MCL-energy recycling fee supported by the energy sector creates a lamp refund process. ‘PRO Lamp’, a producer responsibility organization, will manage the entire system through a widespread public—private agreement.

Proper management of biomedical waste is a crucial issue for maintaining human health and the environment. The waste generated in the hospitals has the potential for spreading infections and causing diseases. The study was conducted by visiting a near by hospital in order to get acquainted with the generation of the biomedical waste and their disposal strategies. The study includes an assortment of details about the quantity of different types of waste generated, their handling, treatment, final disposal and various management strategies adopted by the hospital. The survey was conducted by asking various questions regarding the issue by the waste management team and the workers involved in managing the waste.