Thermal and water ageing effect on mechanical,rheological and morphological properties of glass-fibre-reinforced poly(oxymethylene) composite

Abstract

In this study, the ageing behaviour of glass-fibre-reinforced poly(oxymethylene) composite at different conditions was investigated. The ageing was performed in various controlled environments, namely in air at room temperature, in water at room temperature and in an oven at the temperature of 100 ℃. Tensile and flexural tests were conducted to determine the mechanical properties, melt flow index was measured to determine the rheological property and scanning electron microscopy was used to observe the morphological property of unaged and aged poly(oxymethylene) samples. A reduction in both tensile and flexural strength was observed with all ageing environment. The worst strength retention was obtained with water ageing. Water absorbed by glass-fibre-reinforced poly(oxymethylene) composite had a detrimental influence on the tensile and flexural strength. Tensile strength was affected by the ageing environments. The decrease in the tensile strength of air and thermally aged poly(oxymethylene) was slower than that of water aged poly(oxymethylene), and the tensile strength of aged samples decreased as the ageing time increased. The combined actions of heat, air and water (thermal + water + air ageing) did not further degrade glass-fibre-reinforced poly(oxymethylene) compared to only water ageing at the room temperature. All tensile stress–strain and flexural load–deflection curves showed the similar tendency and did not change with ageing environments and time. All aged samples showed higher melt flow index values than that of unaged sample and the changes in melt flow index could be an indicator of degradation.

Keywords

Ageing composite degradation mechanical properties injection molding

Get full access to this article

View all access options for this article.

References

Lüftl

Archodoulaki

V-M

Glantschnig

et al.

Influence of coloration on initial material properties and on thermooxidative ageing of a polyoxymethylene copolymer. J Mater Sci 2007; 42: 1351–1359.

Cai

et al.

Mechanical properties and solid-state structure of photodegraded polyoxymethylene and effect of UV stabilizers modification. J Macromol Sci Part B Phys 2011; 50: 1521–1534.

Archodoulaki

V-M

Lüftl

Seidler

. Effects of coloration on the physical and mechanical properties and on the thermal stability of polyoxymethylene. Adv Polym Technol 2006; 25: 63–72.

Lüftl

Archodoulaki

V-M

Koch

et al.

Effects of the additive package on the thermal properties of a commercial polyoxymethylene homopolymer. J Vinyl Addit Technol 2008; 14: 21–27.

Lüftl

Archodoulaki

V-M

Seidler

. Thermal-oxidative induced degradation behaviour of polyoxymethylene (POM) copolymer detected by TGA/MS. Polym Degrad Stab 2006; 91: 464–471.

Ping

Ting

Ming

et al.

Investigation of the thermal decomposition properties of polyoxymethylene. J Wuhan Univ Technol 2007; 22: 171–173.

Archodoulaki

V-M

Lüftl

Seidler

. Thermal degradation behaviour of poly(oxymethylene): 1. Degradation and stabilizer consumption. Polym Degrad Stab 2004; 86: 75–83.

Archodoulaki

V-M

Lüftl

Koch

et al.

Property changes in polyoxymethylene (POM) resulting from processing, ageing and recycling. Polym Degrad Stab 2007; 92: 2181–2189.

Archodoulaki

V-M

Lüftl

Seidler

. Oxidation induction time studies on the thermal degradation behaviour of polyoxymethylene. Polym Testing 2006; 25: 83–90.

10.

ISO 527:1997. Plastics – determination of tensile properties.

11.

ISO 178:2010. Plastics – determination of flexural properties.

12.

ISO 1133:2005. Plastics – determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics.

13.

Espert

Vilaplana

Karlsson

. Comparison of water absorption in natural cellulosic fibres from wood and one-year crops in polypropylene composites and its influence on their mechanical properties. Compos Part A 2002; 35: 1267–1276.

14.

Dhakal

Zhang

Richardson

MOW

. Effect of water absorption on the mechanical properties of hemp fibre reinforced unsaturated polyester composites. Compos Sci Technol 2007; 67: 1674–1683.

15.

Shinoj

Panigrahi

Visvanathan

. Water absorption pattern and dimensional stability of oil palm fiber-linear low density polyethylene composites. J Appl Polym Sci 2010; 117: 1064–1075.

16.

Grammatikos

Zafari

Evernden

et al.

Moisture uptake characteristics of a pultruded fibre reinforced polymer flat sheet subjected to hot/wet aging. Polym Degrad Stab 2015; 121: 407–419.

17.

Crank J. The mathematics of diffusion. Bristol, England: Clarendon Press, 1975.

18.

Shen

C-H

Springer

. Moisture absorption and desorption of composite materials. J Compos Mater 1976; 10: 2–20.

19.

Boubakri

Haddar

Elleuch

et al.

Impact of aging conditions on mechanical properties of thermoplastic polyurethane. Mater Des 2010; 31: 4194–4201.

20.

Haddar

Ksouri

Kallel

et al.

Effect of hygrothermal ageing on the monotonic and cyclic loading of glass fiber reinforced polyamide. Polym Compos 2014; 35: 501–508.

21.

Jefferson

Farah

Hempowicz

et al.

Influence of hygrothermal aging on carbon nanofiber enhanced polyester material systems. Compos Part B 2015; 78: 319–323.

22.

Jiang

Kolstein

Bijlaard

FSK

. Moisture diffusion in glass-fiber-reinforced polymer composite bridge under hot/wet environment. Compos Part B 2013; 45: 407–416.

23.

Guermazi

Tarjem

Ksouri

et al.

On the durability of FRP composites for aircraft structures in hygrothermal conditioning. Compos Part B 2016; 85: 294–304.

24.

Ishak

ZAM

Ishiaku

Karger-Kocsis

. Microstructure-related fracture behaviour of injection moulded short fibre reinforced polyarylamide in dry and wet states. J Mater Sci 1998; 33: 3377–3389.

25.

Joseph

Thomas

Pavithran

. Effect of ageing on the physical and mechanical properties of sisal-fiber-reinforced polyethylene composites. Compos Sci Technol 1995; 53: 99–110.

26.

Firdosh

Murthy

HNN

Pal

et al.

Durability of GFRP nanocomposites subjected to hygrothermal ageing. Compos Part B 2015; 69: 443–451.

27.

Assarar

Scida

El Mahi

et al.

Influence of water ageing on mechanical properties and damage events of two reinforced composite materials: flax-fibres and glass-fibres. Mater Des 2011; 32: 788–795.

28.

Yang

Zhang

Zhou

et al.

Effect of fiber surface modification on water absorption and hydrothermal aging behaviors of GF/pCBT composites. Compos Part B 2015; 82: 84–91.

29.

de Albuquerque

Joseph

de Carvalho

et al.

Effect of wettability and ageing conditions on the physical and mechanical properties of uniaxially oriented jute-roving-reinforced polyester composites. Compos Sci Technol 2000; 60: 833–844.

30.

Fouad

. Effect of long-term natural aging on the thermal, mechanical, and viscoelastic behaviour of biomedical grade of ultra high molecular weight polyethylene. J Appl Polym Sci 2010; 118: 17–24.

31.

Al-Ma’adeed

Al-Qaradawi

Madi

et al.

The effect of gamma irradiation and shelf aging in air on the oxidation of ultra-high molecular weight polyethylene. Appl Surf Sci 2006; 252: 3316–3322.

32.

Thwe

Liao

. Effects of environmental aging on the mechanical properties of bamboo-glass fiber reinforced polymer matrix hybrid composites. Compos Part A 2002; 33: 43–52.

33.

Kollia

Loutas

Fiamegkou

et al.

Degradation behavior of glass fiber reinforced cyanate ester composites under hydrothermal ageing. Polym Degrad Stab 2015; 121: 200–207.

34.

Kakroodi

Kazemi

Rodrigue

. Mechanical, rheological, morphological and water absorption properties of maleated polyethylene/hemp composites: effect of ground tire rubber addition. Compos Part B 2013; 51: 337–344.